Klipper配置远程+近程双挤出机

资源下载
机型:VORON 0
更新日期:22/04/2021
  • 两个挤出机,一个再近程,一个再远程
  • 此办法可以混合实用挤出机,比如近程bmg远程M4
  • 我想要这么搞的原因是,这样对近程挤出机要求很低,提供一点压力,就可以非常顺的打印。 远程会释放近程挤出机的压力
  • 此方式需要调整挤出机压紧轮的压力,因为压力会影响到挤出机的挤出长度,除非用供料管,不然两个挤出机之间的长度会有变化
##  In E0-MOT Position
[extruder]
step_pin: PD5
dir_pin: PD6
enable_pin: !PD4

##  Update value below when you perform extruder calibration
##  If you ask for 100mm of filament, but in reality it is 98mm:
##  rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
##  22.6789511 is a good starting point
rotation_distance: 25.12    #bmg 
##  Update Gear Ratio depending on your Extruder Type
##  Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
##  Use 80:20 for M4, M3.1
gear_ratio: 50:17               #BMG Gear Ratio
microsteps: 32
full_steps_per_rotation: 200    #200 for 1.8 degree, 400 for 0.9 degree
nozzle_diameter: 0.400
filament_diameter: 1.75
##      In E0 OUT Position
heater_pin: PB15
##  Validate the following ATC Semitec 104GT-2 thermistor type to make sure it is correct
#sensor_type: ATC Semitec 104GT-2
sensor_type: PT1000
sensor_pin: PC0
pullup_resistor: 4700
min_temp: 10
max_temp: 270
max_power: 1.0
min_extrude_temp: 170
control = pid
pid_kp = 26.213
pid_ki = 1.304
pid_kd = 131.721
##  Try to keep pressure_advance below 1.0
pressure_advance: 0.05
##  Default is 0.040, leave stock
pressure_advance_smooth_time: 0.040

##  In E0-MOT Position
##  Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 extruder]
uart_pin: PD7
interpolate: false
run_current: 0.6
hold_current: 0.6
sense_resistor: 0.110
stealthchop_threshold: 0

##重点在下面
##  In E4-MOT Position
[extruder_stepper my_extra_stepper]
extruder = extruder  #同步到extruder上
step_pin: PE1
dir_pin: PE0
enable_pin: !PC5
microsteps:32
rotation_distance: 25.12    #bmg 
gear_ratio: 50:17               #BMG Gear Ratio
full_steps_per_rotation: 200    #200 for 1.8 degree, 400 for 0.9 degree
#shared_heater: extruder
#nozzle_diameter: 0.400
#filament_diameter: 1.75

##  In E4-MOT Position
##  Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 extruder_stepper my_extra_stepper]
uart_pin: PD11

interpolate: false
run_current: 0.6
hold_current: 0.6
sense_resistor: 0.110
stealthchop_threshold: 0
资源下载
2
封面图
  • 评论4

    请先

    1. 大佬,没看明白
      txctzl198805-17
    2. 想明白了,两个挤出机,一个在近端,一个在远端,同时发力?这个要求电机和挤出机都一样才更好吧,配置,电流都要一样。
      txctzl198805-17
    3. 先要把两个挤出机,的步进值微调到一致吧。
      txctzl198805-17
    没有账号? 注册  忘记密码?

    社交账号快速登录